Page 12 of 17
Re: The 928 Photo Thread
Posted: Fri Jun 17, 2022 3:43 pm
by h2pmr
a first attempt at a replica of a 92862404900, a protection plate that fits behind the tail gate opening motor, i guess to stop potential damage to it or the warning triangle itself when the warning triangle is removed/ refitted.
its NLA from Porsche.
genuine Porsche one on the left, mine on the right, just need to get the indentations deeper on the next one, then stick a few on ebay, should sell like hot cakes...
cheers
Phil
Re: The 928 Photo Thread
Posted: Sun Jun 19, 2022 3:06 am
by Strosek Ultra
Think I can show this without being called a copy cat by someone.
Åke
Re: The 928 Photo Thread
Posted: Sun Jun 19, 2022 5:13 am
by h2pmr
Strosek Ultra wrote:Think I can show this without being called a copy cat by someone.
Åke
plenty of knowledge without the ego's = a far more easy going forum in my opinion
Re: The 928 Photo Thread
Posted: Sun Jun 19, 2022 1:31 pm
by XR4Tim
Re: The 928 Photo Thread
Posted: Sat Jul 09, 2022 6:57 am
by h2pmr
innards of an in tank fuel pump
Re: The 928 Photo Thread
Posted: Sat Jul 09, 2022 10:44 am
by worf
Strosek Ultra wrote: ↑Sun Jun 19, 2022 3:06 am
Think I can show this without being called a copy cat by someone.
Nice. What are you doing for a pickup tube spacer.
Edit: Forgot picture…
(Oh, BTW, if you want to post a bunch of pictures, this site’s thread navigation and pagination work better when it’s one to three pictures per post.)
Re: The 928 Photo Thread
Posted: Sun Jul 10, 2022 10:02 am
by Crumpler
More speed, more brake.
GTS calipers from Kevin.
Re: The 928 Photo Thread
Posted: Wed Jul 13, 2022 4:48 pm
by Bertrand Daoust
Once a year wheel well cleaning today!
Re: The 928 Photo Thread
Posted: Wed Jul 13, 2022 8:36 pm
by Crumpler
Re: The 928 Photo Thread
Posted: Thu Jul 14, 2022 2:56 pm
by h2pmr
Crumpler wrote:
water cooled intercooler?
Re: The 928 Photo Thread
Posted: Thu Jul 14, 2022 9:59 pm
by Crumpler
Bingo Phil :)
It’s a small core but the only place I could get an intercooler to fit. The centrifugal SC was heat soaking badly.
Re: The 928 Photo Thread
Posted: Thu Jul 14, 2022 10:56 pm
by XR4Tim
Re: The 928 Photo Thread
Posted: Fri Jul 15, 2022 11:21 am
by worf
XR4Tim wrote: ↑Thu Jul 14, 2022 10:56 pm
... pic ...
NOS right-side parcel shelf?
Re: The 928 Photo Thread
Posted: Fri Jul 15, 2022 9:29 pm
by XR4Tim
worf wrote: ↑Fri Jul 15, 2022 11:21 am
XR4Tim wrote: ↑Thu Jul 14, 2022 10:56 pm
... pic ...
NOS right-side parcel shelf?
Yes!
Re: The 928 Photo Thread
Posted: Wed Jul 27, 2022 6:35 am
by Bertrand Daoust
From this year PVGP,
Re: The 928 Photo Thread
Posted: Mon Aug 01, 2022 11:20 pm
by worf
Quiz:
Re: The 928 Photo Thread
Posted: Tue Aug 02, 2022 3:19 pm
by h2pmr
no need to get the apprentice to try and make some out of a cut off bolt head, i have a few spare if you need any
other than that i am out of ideas
cheers
Phil
Re: The 928 Photo Thread
Posted: Tue Aug 02, 2022 5:09 pm
by Rdon
“Flappy valve” stop
Re: The 928 Photo Thread
Posted: Tue Aug 02, 2022 5:20 pm
by Rdon
Re: The 928 Photo Thread
Posted: Thu Aug 04, 2022 7:54 pm
by worf
@Rdon Your picture: $1000 of pain.
Rdon wrote: ↑Tue Aug 02, 2022 5:09 pm
“Flappy valve” stop
Correct!
Re: The 928 Photo Thread
Posted: Fri Aug 05, 2022 7:44 am
by Rdon
worf wrote: ↑Thu Aug 04, 2022 7:54 pm
@Rdon Your picture: $1000 of pain.
Fortunately, the pump is operational. Removed it specifically to check for a broken hose and was not disappointed. No drama with the threaded insert, replacement hose and clamps installed and now, theoretically, one less thing that could leave me on the side of the road.
Re: The 928 Photo Thread
Posted: Sat Aug 27, 2022 4:28 am
by Strosek Ultra
Things does not always go well. In this case fabricating a new wrist pin bushing is all what was needed except for a new wrist pin.
Åke
Re: The 928 Photo Thread
Posted: Sat Aug 27, 2022 7:35 am
by h2pmr
Strosek Ultra wrote:
Things does not always go well. In this case fabricating a new wrist pin bushing is all what was needed except for a new wrist pin.
Åke[/quote
interested to know more about what happened to that wrist pin
cheers
Phil
Re: The 928 Photo Thread
Posted: Sun Aug 28, 2022 3:41 am
by Strosek Ultra
Re: The 928 Photo Thread
Posted: Sun Aug 28, 2022 4:42 am
by h2pmr
/\ /\ /\ /\
so i guess he's not perfect after all
cheers
Phil
Re: The 928 Photo Thread
Posted: Sun Aug 28, 2022 6:51 am
by Strosek Ultra
h2pmr wrote: ↑Sun Aug 28, 2022 4:42 am
/\ /\ /\ /\
so i guess he's not perfect after all
cheers
Phil
Nobody is perfect. I do not know how involved he was in this disaster.
You can read more here (page 7).
https://www.corner-carvers.com/forums/s ... ing-thread
Åke
Re: The 928 Photo Thread
Posted: Sun Aug 28, 2022 12:07 pm
by h2pmr
Strosek Ultra wrote:h2pmr wrote: ↑Sun Aug 28, 2022 4:42 am
/\ /\ /\ /\
so i guess he's not perfect after all
cheers
Phil
Nobody is perfect. I do not know how involved he was in this disaster.
You can read more here (page 7).
https://www.corner-carvers.com/forums/s ... ing-thread
Åke
thanks for the thread link, i thought it was a recent, road car engine failure but still sadly 1 less useable engine block in the world.
cheers
Phil
Re: The 928 Photo Thread
Posted: Sat Sep 03, 2022 3:28 am
by Strosek Ultra
Strosek cars.
Åke
Re: The 928 Photo Thread
Posted: Sat Sep 03, 2022 5:53 am
by Strosek Ultra
Finally finished painting the three white garage doors.
Åke
Re: The 928 Photo Thread
Posted: Sat Sep 03, 2022 9:54 am
by SeanR
Re: The 928 Photo Thread
Posted: Sat Sep 03, 2022 3:03 pm
by h2pmr
before i get my micrometer out, does anybody know what size bearing or generic part number of it, that fits in the A/C compressor front pulley?
compressor is the 80-89 version.
cheers
Phil
Re: The 928 Photo Thread
Posted: Sun Sep 04, 2022 3:25 am
by Strosek Ultra
image.png
This bearing is a double row angular contact ball bearing. This bearing is usually used in AC compressor / compressors on vehicles, where by the additional names as AC bearing and Kompressor bearing.
FULL DESIGNATION: AC 35x55x20
( d ) INNER DIAMETER: 35 mm
( D ) OUTER DIAMETER: 55 mm
( B ) WIDTH: 20 mm
Åke
Re: The 928 Photo Thread
Posted: Sun Sep 04, 2022 4:07 am
by h2pmr
Strosek Ultra wrote:image.png
This bearing is a double row angular contact ball bearing. This bearing is usually used in AC compressor / compressors on vehicles, where by the additional names as AC bearing and Kompressor bearing.
FULL DESIGNATION: AC 35x55x20
( d ) INNER DIAMETER: 35 mm
( D ) OUTER DIAMETER: 55 mm
( B ) WIDTH: 20 mm
Åke
perfect, many thanks Ake
Re: The 928 Photo Thread
Posted: Mon Sep 05, 2022 5:27 am
by Strosek Ultra
Strosek cars are out and about.
The old man with the walker is not a Porsche owner.
Åke
Re: The 928 Photo Thread
Posted: Sat Sep 10, 2022 10:45 am
by h2pmr
Strosek Ultra wrote:
This bearing is a double row angular contact ball bearing. This bearing is usually used in AC compressor / compressors on vehicles, where by the additional names as AC bearing and Kompressor bearing.
FULL DESIGNATION: AC 35x55x20
( d ) INNER DIAMETER: 35 mm
( D ) OUTER DIAMETER: 55 mm
( B ) WIDTH: 20 mm
Åke
sadly the 80-89 A/C compressor use a bearing 40 x 62 x 24, not quite as easy to find though
Re: The 928 Photo Thread
Posted: Sat Sep 10, 2022 1:21 pm
by h2pmr
i think part number of the bearing is 40BG62020-2DLCS, will order 1 and see if it fits.
cheers
Phil
Re: The 928 Photo Thread
Posted: Sat Sep 10, 2022 6:04 pm
by Bertrand Daoust
A 928 meet today in Montréal.
Thanks Andy!
A lot of fun with great owners.
And two very special guests!
Re: The 928 Photo Thread
Posted: Sat Sep 10, 2022 9:36 pm
by Bertrand Daoust
...
Re: The 928 Photo Thread
Posted: Sun Sep 11, 2022 2:55 am
by Strosek Ultra
h2pmr wrote: ↑Sat Sep 10, 2022 1:21 pm
i think part number of the bearing is 40BG62020-2DLCS, will order 1 and see if it fits.
cheers
Phil
The bearing you need is called 40BD219.
Can be found on Ebay or here
https://www.bearingwholesalelots.com/40 ... on-com.htm
The bearing you mentioned is 20,6mm wide.
Åke
https://www.ebay.com/itm/192305821780?h ... BMhJDStOVg
image.png
Re: The 928 Photo Thread
Posted: Sun Sep 11, 2022 11:11 am
by h2pmr
Strosek Ultra wrote:h2pmr wrote: ↑Sat Sep 10, 2022 1:21 pm
i think part number of the bearing is 40BG62020-2DLCS, will order 1 and see if it fits.
cheers
Phil
The bearing you need is called 40BD219.
Can be found on Ebay or here https://www.bearingwholesalelots.com/40 ... on-com.htm
The bearing you mentioned is 20,6mm wide.
Åke
https://www.ebay.com/itm/192305821780?h ... BMhJDStOVg
image.png
ah yes, managed to cancel that one and get one the correct size, thank you Ake.
Re: The 928 Photo Thread
Posted: Mon Sep 12, 2022 2:06 pm
by SeanR
30 sets are ready to ship. Sorry for the wait boys and girls.
image.png
Re: The 928 Photo Thread
Posted: Sat Sep 17, 2022 6:54 am
by h2pmr
Strosek Ultra wrote:h2pmr wrote: ↑Sat Sep 10, 2022 1:21 pm
i think part number of the bearing is 40BG62020-2DLCS, will order 1 and see if it fits.
cheers
Phil
The bearing you need is called 40BD219.
Can be found on Ebay or here https://www.bearingwholesalelots.com/40 ... on-com.htm
The bearing you mentioned is 20,6mm wide.
Åke
https://www.ebay.com/itm/192305821780?h ... BMhJDStOVg
fitted the bearing yesterday and fits like a glove, many thanks.
Re: The 928 Photo Thread
Posted: Sun Sep 18, 2022 2:58 pm
by h2pmr
lack of use in the UK
Re: The 928 Photo Thread
Posted: Sun Sep 18, 2022 3:00 pm
by h2pmr
N/A to auto owners
Re: The 928 Photo Thread
Posted: Sun Sep 18, 2022 3:13 pm
by h2pmr
more slightly unsafe corrosion
Re: The 928 Photo Thread
Posted: Mon Sep 19, 2022 12:35 am
by worf
Stay in your grove you mutha!@#$ing gasket!
When you get a cam cover gasket that was rolled into a little ball for shipping:
Re: The 928 Photo Thread
Posted: Tue Sep 20, 2022 6:04 pm
by XR4Tim
Re: The 928 Photo Thread
Posted: Mon Sep 26, 2022 1:20 pm
by Strosek Ultra
Porsche meet at Tjällmo, Sweden.
Åke
Re: The 928 Photo Thread
Posted: Mon Sep 26, 2022 1:27 pm
by worf
928 Frenzy. Last Saturday.
Re: The 928 Photo Thread
Posted: Mon Sep 26, 2022 1:28 pm
by SeanR